smellcopper2

Reasons to Change Door Lock You can replace your door lock for a variety of reasons, from upgrading the security of your home to redecorating the entrance. You might also have to change locks if your key gets stuck or is difficult to turn. Change your lock is a simple project that even novice DIY homeowners can tackle. Find the necessary materials to begin. Take off the lock that was previously used. Before installing a new lock, it is necessary to remove the old lock from the door. This is crucial when you suspect that someone else might have a key to the house. It may also be an ideal option if you have moved into a new house, experienced a break-in or had a roommate move in. The process is a lot simpler than you think and can be completed in just a few minutes. Begin by removing the screws that hold the deadbolt faceplate onto the door frame. You'll need to remove the screws on both sides of the door in order to remove the faceplate. This will allow you to discover what's behind it and will give you a better understanding of what to do in the next steps. Once you have removed the old faceplate, then you have to take off the bolt and strike plate. Remove the bolt from the door hole by using the screwdriver. If the bolt is rusted, you may have to use a chisel to hammer it. If you are using a chisel, you must be cautious not to scratch the door frame. Before you take down the lock that was previously in use, make sure that the new doorknob and deadbolt fit into the holes in the door. A lot of hardware stores and big box stores have a wide selection of locks and will assist you in selecting the best one. If the lock you bought doesn't match your door, send it back and ask for assistance. While you're taking off the old lock, look for small slits or depressions in the handle or around the trim. If you find them, you can use a straightened safety-pin or a flat screwdriver to open the handle. Once the screw in the handle has been removed you can begin to remove the knob from its spindle. To do this, locate the set screw at the base of the knob and loosen it. Then, you'll need to remove the knob from the spindle, and carefully remove the spindle from the door. Install the new lock It is a good idea to change locks on doors throughout your home periodically, especially after a burglary or when you move into a room with roommates. It's simple, inexpensive and efficient to change the lock on your door. With Repair My Windows And Doors , and a few basic steps, most people can do it by themselves. You may also want to learn how to rekey your door lock to ensure that only you have the key. You'll need to buy a new lock that has the same keyway as your existing lock. Most locksmiths will rekey your lock for you at an additional cost, but you can save money by doing it yourself. You can buy an entirely new lock from hardware stores or online. A standard deadbolt will usually be able to fit on doors of all sizes however, you'll have to measure the area on your door to ensure that it's a good fit. The lock you purchase will usually come with a diagram that will show you how to install it on the door. It can be used as a guide when drilling the hole which is a lot easier than measuring each time. If the template doesn't exactly match your hole, bring it back to the store and get another one. When installing the new lock, you must remember to put it on the right side of the door. Check the latch. It should be marked with “up” or something similar. Check that the latch is sitting correctly in the latch plate, then secure it with the screws supplied. If you're replacing a door knob lock It's important to be aware of the handing. Most knob locks are left-handed but there are some that are right-handed. If you are not paying attention, the knob could be installed on the wrong side of your door, which will hinder it from locking from the outside or inside. After you've finished testing the new lock to ensure it works. You should be able to lock and unlock the door with keys from the inside as well as the outside. If you're not satisfied with the outcome then you can always call an expert locksmith to fix the issue. Test the lock If a lock on your door isn't able to be opened can be frustrating, it can also put your family's safety at risk. It's easy to solve the majority of door lock issues by tackling the issue and lubrication. Verify that the key has been properly cut, and that the lock assembly is not dirty or loose. If this does not solve the problem Try lubricating the door lock actuator using graphite powdered. Check that the door lock switch, the wiring harnesses and the actuator connector are working properly. Check the wiring diagram or manual to determine the color-coding and function of each door lock switch wire. Use a digital meter or test light to check if the actuator is receiving power and ground when the switches are turned on. If you notice a voltage toggle with each switch activation, that means the switches are working and it's probably the actuator that needs to be replaced. If the switch appears to work but the actuator doesn't move when you turn the knob it could be a problem with the actuator cylinder itself. The actuator cylinder is loaded with spring pins that prevent the cylinder from turning until a key is inserted and it pushes the pins up to fit the key's height in that location. This causes the cylinder eventually to turn and open the lock body and allowing the latch to open for the handle. If the door lock actuator is still not functioning, you can remove it by using a small screwdriver. You will need to release the bolt that locks first, and then separate the plastic cover which holds the electrical connector. Then, disconnect the door actuator from the lock and let it fall down. You should then be able find the two bolts in 10mm that hold the actuator in place and then remove them. After the actuator has been removed then you can disconnect the black electrical connector. Replace the key If your deadbolt is locked or door knob is not functioning, you'll have to rekey it or replace it. This isn't difficult and can save you money. It is recommended to have a professional locksmith check the locks for any problems before you start. This will give you peace of mind that your home is safe and safe. Remove the exterior faceplate of the doorknob/deadbolt. If there are screws that hold the faceplate, use a screwdriver and take it off. Then, remove the interior faceplate using a flat-head screwdriver. After you have removed the faceplate, you can take the bolt and screw from the lock cylinder. A locksmith can help determine if the existing lock needs to be replaced or changed. They can also offer advice on the best security measures for your home. They will also make any necessary adjustments to the door or frame to ensure a perfect fit. They will also provide an assurance on their work. You will need to purchase a brand new lock key before you are able to change it. It is crucial to select a lock key that fits snugly. If you use a key that isn't right, it could damage the mechanism's internal mechanisms and prevent it from functioning. Insert the key into the lock to check its size. If the key fits completely against the plug then it's the right size. If the pins protrude out of the top of the plug, they're too long. You may want to change the lock on your door for a variety of reasons, such as: Rekeying a lock is an affordable alternative to replacing it if you are moving into the home of a previous owner or if your keys have gone missing. It is also less invasive than a full replacement. However, there are certain situations in which rekeying your lock isn't feasible. If the lock has been damaged or jammed repeatedly, for example, it may be the right time to replace it.